消防泡沫炮能很好地防止火灾，广泛用于各种公共场所和高大空间。然而，一切都有失败的可能，消防泡沫炮也不例外。为此，小编就为大家总结一下消防泡沫炮存在的问题及故障分析。

Fire foam monitor can prevent fire well and is widely used in various public places and large spaces. However, everything has the possibility of failure, and the fire foam monitor is no exception. To this end, I will summarize the problems and fault analysis of fire foam monitor for you.

消防泡沫炮故障问题分析：

Fault analysis of fire foam monitor:

消防中心无法远程启停消防炮

The fire control center cannot start or stop the fire monitor remotely

当消防中心无法远程启动或停止消防炮时，检查电路是否开路或断路，并检查和维护电路，看看在原线路释放时是否有备用电路；二是非标联动柜按钮开关连接不良或多线控制板松动损坏。多线控制板损坏，检查维修设备。

When the fire control center cannot start or stop the fire monitor remotely, first check whether the circuit is open or open, and check and maintain the circuit to see if there is a backup circuit when the original circuit is released; Second, the button switch of non-standard linkage cabinet was poorly connected or the multi wire control board was loose and damaged. The multi line control board is damaged. Check and repair the equipment.

消防炮启动后管网无法加压

The pipe network cannot be pressurized after the fire monitor is started

一般来说，除了消防炮本身之外，还有两种常见的故障。管网中空气过多。管网抽空，再对消防炮加压。二是消防炮在地上，水池在地下，消防炮在地上。与水池相连的管网下方有一个吸水底阀。由于吸入底阀不能停水，管网内充满空气，消防炮启动后不能打开吸入底阀，吸不到水。向上压并检修吸入底阀。

Generally speaking, in addition to the fire monitor itself, there are two common faults. There is too much air in the pipe network. The pipe network is evacuated and the fire monitor is pressurized. Second, the fire monitor is on the ground, the pool is underground, and the fire monitor is on the ground. There is a suction bottom valve under the pipe network connected with the pool. Since the suction bottom valve cannot stop water supply and the pipe network is full of air, the suction bottom valve cannot be opened after the fire monitor is started, and water cannot be sucked. Press upward and repair the suction bottom valve.

消防泡沫炮的出水口既不是柱状也不是雾状

The water outlet of fire foam monitor is neither columnar nor foggy

安装水炮前，需要在与消防管网连接的电磁阀前安装过滤器，消防管网必须对软管加压，将管内的污物或焊渣吹出。防止管道内容物在高压冲击下损坏阀门。其次，会影响水炮的出水量。如果整流器中有东西堵塞，水炮输出的水既不是柱状也不是雾状的。这个时候，如果要处理，川消人员建议需要厂家的人员了。

Before installing the water monitor, it is necessary to install a filter in front of the solenoid valve connected to the fire pipe network. The fire pipe network must pressurize the hose to blow out the dirt or welding slag in the pipe. Prevent pipeline contents from damaging the valve under high pressure impact. Secondly, it will affect the water output of the water cannon. If something in the rectifier is blocked, the water output from the water cannon is neither columnar nor foggy. At this time, if it needs to be handled, the Sichuan consumer suggested that the manufacturer's professionals be needed.

希望以上介绍对你有帮助。需要再次强调的是，当消防泡沫炮发生故障时，不要着急，只要遵循合理的方法，通过检查方法很容易问题。更多内容就来网站www.cx-fire.com咨询了解吧！

I hope the above introduction is helpful to you. It should be emphasized again that when the fire foam monitor breaks down, do not worry. As long as you follow reasonable methods, it is easy to solve the problem through inspection methods. For more information, please visit www.cx-fire Www. 68mn!